BOWL BLANKS

$10

 ADDED 1/29/2018

This is for an STL ONLY file of the item(s) below. You can use meshmixer to combine them with other STL files and save as one STL file that you can import into Vcarve Desktop or Pro. 

$12

MOST FILES NOW AVAILABLE ON ETSY AS INSTANT DOWNLOADS!!!

INCLUDES:


  • 7 STL FILES
  • TWO NESTED END TO END (ONE WITHOUT THE TABLE SPOON UNDER 30")
  • SIZES 1/4, 1/3, 1/2, 3/4, 1
  • END RESULTS ARE NESTABLE (FIT INSIDE EACH OTHER)

TABLESPOONS

INCLUDES:


  • ​10 INDIVIDUAL MODELS IN THE FOLLOWING SIZES

INCLUDES:


  • 8 INDIVIDUAL MODELS. 4 SQUARE AND 4 RECTANGULAR.

After payment, you will receive 1 email with a single zip folder. Please allow up to 48 hours to receive the Email. This is non refundable. If I catch my model in any free forum, I will seek penalties.

After payment, you will receive 1 email with a single zip folder. Please allow up to 48 hours to receive the Emails. This is non refundable. If I catch my model in any free forum, I will seek penalties.

INCLUDES:


  • 5 STL FILES
  • INCLUDES A NOODLE SPOON

This is for an STL ONLY file of the item(s) below. You can use meshmixer to combine them with other STL files and save as one STL file that you can import into Vcarve Desktop or Pro. 

INCLUDES:


  • 7 STL FILES
  • NARROW SPOONS
  • WIDE SPOONS
  • SMALL SPOONS
  • LOW PROFILE SPOONS

$12

 ADDED 8/29/2018

This is for an STL ONLY file of the item(s) below. You can use meshmixer to combine them with other STL files and save as one STL file that you can import into Vcarve Desktop or Pro. 

 ADDED 1/22/2019

TEASPOONS

EATING AND SOUP SPOONS

 ADDED 1/29/2018

SPATULAS

SQUARE AND RECTANGLE DISH BLANKS

INCLUDES:


  • 10 INDIVIDUAL MODELS    NOW WITH 18!!!!
  • ANGLED RIMS
  • ROUND RIMS
  • CURVED RIMS
  • MOST ARE 2 SIDED

For my file sales, I am taking the taxes out on my end so you will not see the newly required sales tax on all internet sales (new Wisconsin state law).

DESIGNS BY PHIL, LLC

After payment, you will receive 1 email with a single zip folder. Please allow up to 48 hours to receive the Email. This is non refundable. If I catch my model in any free forum, I will seek penalties.

ROUND PLATE BLANKS

3" DIAMETER X 1.44" TALL

4" DIAMETER X 1.44" TALL

6" DIAMETER X 1.44" TALL

6" DIAMETER X 2.00" TALL

6" DIAMETER X 2.50" TALL

8" DIAMETER X 3.44" TALL

10" DIAMETER X 3.44" TALL

12" DIAMETER X 3.44" TALL

14" DIAMETER X 3.44" TALL

16" DIAMETER X 3.44" TALL

INCLUDES:


  • 6 STL FILES
  • ONE NESTED END TO END
  • SIZES 1/4, 1/3, 1/2, 3/4, 1
  • END RESULTS ARE NESTABLE (FIT INSIDE EACH OTHER)

 ADDED 1/29/2018

This is for an STL ONLY file of the item(s) below. You can use meshmixer to combine them with other STL files and save as one STL file that you can import into Vcarve Desktop or Pro. 

After payment, you will receive 2 emails with a single zip folder in each. Please allow up to 48 hours to receive the Emails. This is non refundable. If I catch my model in any free forum, I will seek penalties.

 ADDED 1/22/2019

 ADDED 8/29/2018

PLATES, BOWLS, AND SPOONS

After payment, you will receive 1 email with a single zip folder. Please allow up to 48 hours to receive the Emails. This is non refundable. If I catch my model in any free forum, I will seek penalties.

$12

$12

After payment, you will receive 3 emails with a single zip folder in each. Please allow up to 48 hours to receive the Emails. This is non refundable. If I catch my model in any free forum, I will seek penalties.

(CLICK TO ENLARGE)

This is for an STL ONLY file of the item(s) below. You can use meshmixer to combine them with other STL files and save as one STL file that you can import into Vcarve Desktop or Pro. 

This is for an STL ONLY file of the item(s) below. You can use meshmixer to combine them with other STL files and save as one STL file that you can import into Vcarve Desktop or Pro. 

$12

(CLICK TO ENLARGE)

$12

After payment, you will receive 1 email with a single zip folder. Please allow up to 48 hours to receive the Emails. This is non refundable. If I catch my model in any free forum, I will seek penalties.

This is for an STL ONLY file of the item(s) below. You can use meshmixer to combine them with other STL files and save as one STL file that you can import into Vcarve Desktop or Pro.